有个问题,急需解决!~

[Eagle_ice]

大家好~我使用的设备是一台HP7203 两台7102路由器和两太HP2626交换机还有两台PC机做RIP协议的验证!各设备端口已经配置好！详情请看下面的结果～！哪位兄弟给详细分析一下，小弟初学！不懂的很多！谢谢了
注释：eth为以太网端口　e１为ＷＡＮ端口
结果如下：
7102A(config)#do show ip route
Codes: C - connected, S - static, R - RIP, O - OSPF, B - BGP
IA - OSPF inter area, N1 - OSPF NSSA external type 1
N2 - OSPF NSSA external type 2, E1 - OSPF external type 1
E2 - OSPF external type 2

Gateway of last resort is not set

C 10.1.1.0/24 is directly connected, eth 0/1
R 10.1.2.0/24 [120/1] via 10.1.1.2, eth 0/1
C 10.1.3.0/24 is directly connected, eth 0/2
R 10.1.4.0/24 [120/1] via 192.168.1.2, ppp 1
C 192.168.1.0/24 is directly connected, ppp 1
C 192.168.1.2/32 is directly connected, ppp 1

7102B(config)#do show ip route
Codes: C - connected, S - static, R - RIP, O - OSPF, B - BGP
IA - OSPF inter area, N1 - OSPF NSSA external type 1
N2 - OSPF NSSA external type 2, E1 - OSPF external type 1
E2 - OSPF exter

Gateway of last resort is not set

R 10.1.1.0/24 [120/1] via 10.1.2.2, eth 0/1
C 10.1.2.0/24 is directly connected, eth 0/1
R 10.1.3.0/24 [120/1] via 192.168.1.1, ppp 1
C 10.1.4.0/24 is directly connected, eth 0/2
C 192.168.1.0/24 is directly connected, ppp1
C 192.168.1.1/24 is directly connected, ppp1


ProCurveSR7203dl(config)#do show ip route
Codes: C - connected, S - static, R - RIP, O - OSPF, B - BGP
IA - OSPF inter area, N1 - OSPF NSSA external type 1
N2 - OSPF NSSA external type 2, E1 - OSPF external type 1
E2 - OSPF external type 2

Gateway of last resort is not set

C 10.1.1.0/24 is directly connected, eth 0/1
C 10.1.2.0/24 is directly connected, eth 0/2
R 10.1.3.0/24 [120/1] via 10.1.1.1, eth 0/1
R 10.1.4.0/24 [120/1] via 10.1.2.1, eth 0/2
R 192.168.1.0/24 [120/1] via 10.1.1.1, eth 0/1

交换机：
2626A Vlan 1 10.1.3.2 255.255.255.0
2626B Vlan 1 10.1.4.2 255.255.255.0
ＰＣ机：
PC1 10.1.3.3 255.255.255.0 10.1.3.1
PC2 10.1.4.3 255.255.255.0 10.1.4.1

[mohuaiyuan]

就几个路由表嘛，对着拓扑图一分析就晓得了

[ibuzuosf]

up

[hahe777888]

交换机：
2626A Vlan 1 10.1.3.2 255.255.255.0
2626B Vlan 1 10.1.4.2 255.255.255.0
ＰＣ机：
PC1 10.1.3.3 255.255.255.0 10.1.3.1
PC2 10.1.4.3 255.255.255.0 10.1.4.1
这个就是你的路由表嘛PC1是在VLAN 1的10.1.3的网段,PC2是在VLAN 1的10.1.4的网段,且VLAN 1,2的IP分别是3.2和4.2,PC1和PC2的IP是就3.3和4.3,路由的IP 分别是3.1和4.1...........

[UltraBejing]

支持搂主，收藏