4,356
社区成员
发帖
与我相关
我的任务
分享懂SCO openserver 5的朋友帮个忙（答得上一定给分）
安装系统时未选网卡，系统安装完成后，配置网卡时发现自己的网卡不在列表中（我的网卡是华硕主板上带的Realtek® RTL 8139C，在网上查了这种网卡支持SCO openserver 5，如何安装？
...全文
请发表友善的回复…
发表回复
yijn 2001-08-31
- 打赏
- 举报
to njbfy(bfy)南京的朋友，谢谢提醒，这个我知道！
njbfy 2001-08-31
- 打赏
- 举报
from 'your computer'是从你的计算机, 即本机.
yijn 2001-08-31
- 打赏
- 举报
to thorn(thorn)
说明里面确实是这么说的，但运行custom时，选Software"-> "Install New" -> "From 'computerNAME'"居然用了2个小时还没有动静，昨天我又在X-WINDOWS系统下情况照旧，神啦，救救我吧！
附上该网卡的README文件
SCO UNIX 5.X
Introduction:
This document describes the procedure to install the SCO UNIX driver
for REALTEK RTL8139 PCI ethernet adapter.
Location of Driver: \SCO\5.X\8139.VOL
Installing driver procedure on SCO UNIX :
Before you start with the installation process, make sure that the
SCO UNIX system is properly installed. Similarly,your adapter should
also be properly installed in your machine.
1. Installation Diskette in DOS format.
Put RTL SCO UNIX Driver diskette to floppy A: and use doscp
command to copy RTL SCO UNIX PCI Driver into UNIX's directories.
# cd /
# doscp A:setup /setup
# chmod +x /setup
# ./setup
Then, the install program will ask you for path of the files,
you can key in:
a:/sco/5.x
or
b:/sco/5.x
2. Run 'custom' utility to add RTL8139 driver software to system.
Select the following option::
"Software"
-> "Install New"
-> "From 'your computer'"
-> 'MediaImages"
Then enter the directory of driver image(8139.VOL) which
should be "/tmp"
3. Use netconfig utility
Avaiable options:
# netconfig
4. To add adapters, select "Add New Lan Adapter" from "Hardware".
5. Select the line speed from the menu:
(1)Hwset,(2)Auto,(3)10half.(4)10full.(5)100half.(6)100full.
if you select Hwset, driver will read configuration from EEPROM
on the card. the configuration can be modified by running
'rset8139' in the driver disk. The program is for DOS.
6. Add Protocol to select SCO TCP/IP.
7. Enter the internet Address of this interface,
for example : 192.9.9.1
8. Enter the netmask for this interface
(default 255.255.255.0)
9. Enter the boardcast address for this interface
use default: n.n.n.n
10. Do you want to relink to kernel now ? (y/n)
type in 'y'
11. Do you want this kernel to boot by default (y/n)
type in 'y'
11. Do you want the kernel environment rebuilt (y/n)
type in 'y'
12. Reboot unix
# shutdown -y -g0
说明里面确实是这么说的，但运行custom时，选Software"-> "Install New" -> "From 'computerNAME'"居然用了2个小时还没有动静，昨天我又在X-WINDOWS系统下情况照旧，神啦，救救我吧！
附上该网卡的README文件
SCO UNIX 5.X
Introduction:
This document describes the procedure to install the SCO UNIX driver
for REALTEK RTL8139 PCI ethernet adapter.
Location of Driver: \SCO\5.X\8139.VOL
Installing driver procedure on SCO UNIX :
Before you start with the installation process, make sure that the
SCO UNIX system is properly installed. Similarly,your adapter should
also be properly installed in your machine.
1. Installation Diskette in DOS format.
Put RTL SCO UNIX Driver diskette to floppy A: and use doscp
command to copy RTL SCO UNIX PCI Driver into UNIX's directories.
# cd /
# doscp A:setup /setup
# chmod +x /setup
# ./setup
Then, the install program will ask you for path of the files,
you can key in:
a:/sco/5.x
or
b:/sco/5.x
2. Run 'custom' utility to add RTL8139 driver software to system.
Select the following option::
"Software"
-> "Install New"
-> "From 'your computer'"
-> 'MediaImages"
Then enter the directory of driver image(8139.VOL) which
should be "/tmp"
3. Use netconfig utility
Avaiable options:
# netconfig
4. To add adapters, select "Add New Lan Adapter" from "Hardware".
5. Select the line speed from the menu:
(1)Hwset,(2)Auto,(3)10half.(4)10full.(5)100half.(6)100full.
if you select Hwset, driver will read configuration from EEPROM
on the card. the configuration can be modified by running
'rset8139' in the driver disk. The program is for DOS.
6. Add Protocol to select SCO TCP/IP.
7. Enter the internet Address of this interface,
for example : 192.9.9.1
8. Enter the netmask for this interface
(default 255.255.255.0)
9. Enter the boardcast address for this interface
use default: n.n.n.n
10. Do you want to relink to kernel now ? (y/n)
type in 'y'
11. Do you want this kernel to boot by default (y/n)
type in 'y'
11. Do you want the kernel environment rebuilt (y/n)
type in 'y'
12. Reboot unix
# shutdown -y -g0
yijn 2001-08-30
- 打赏
- 举报
kmyangyl，能否详细点
yijn 2001-08-30
- 打赏
- 举报
我已经下载了该网卡的SCO驱动，同时拷入系统中，但运行custom时，选Software" -> "Install New" -> "From 'computerNAME'"居然用了2个小时还没有动静，除了屏幕上有个*在滚动表示没死机，这正常吗？
boclif 2001-08-30
- 打赏
- 举报
一般顺序是先安装驱动程序然后就可以找得到该网卡，后配TCP就可以了。
我有一个D＿LINK网卡关于SCO的安装说明，你可以参照一下
D-Link DFE-530TX PCI Fast Ethernet Adapter Installation
for SCO OpenServer V5.0 MDI Driver
Getting Started
---------------
0. Login as root user. (On maintenance mode)
1. Using "custom" to install the driver
1.1 Prepare an image file
Copy d5B.IMG onto SCO OpenServer and rename it to VOL.000.000
# mkdir /usr/test
# doscp a:/<PATH>/d5B.IMG /usr/test/VOL.000.000
* <PATH> is the driver directory
1.2 Execute "custom"
/* A menu selection screen will be popped up */
Using [->] key to move cursor to "Software" menu item then
press [] key to get into pull down menu then move to
"Install New..." then press [ENTER] key
赏屯屯屯屯?Begin Installation on scoopen 屯屯屯屯屯?
? ?
? What host (machine) do you want to install from? ?
? ?
? 谀哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪目 ?
? ?*> From scoopen ??
? ? > From another host ??
? 滥哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪馁 ?
? ?
耗哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪?
篬 Continue ] [ Cancel ] [ Help] ?
韧屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯?
Select From scoopen and use [TAB] key to move cursor to
[ Continue ] then press [ENTER] key and press [] key to get
into pull down menu
赏屯屯屯屯屯屯屯屯屯屯屯?Select Media 屯屯屯屯屯屯屯屯屯屯屯屯?
? ?
? Insert media, and select media device. ?
? ?
? 谀哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪目 ?
? Media Device:硘Floppy Disk Driver 0_____________________|v??
? 郎屯屯屯屯屯屯屯屯屯屯屯屯荒哪哪哪哪哪哪哪哪馁 ?
? 黑哪哪哪哪哪哪哪哪哪哪哪亢 ?
? 撼*Floppy Disk Driver 0 澈 ?
? 撼 Media Images 澈 ?
耗哪哪哪哪哪哪哪暮滥哪哪哪哪哪哪哪哪哪哪馁耗哪哪哪哪哪哪哪哪哪暮
篬 Continue ] 韧屯屯屯屯屯屯屯屯屯屯屯图 [ Help ]?
韧屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯图
-> Select "Media Images" and use [TAB] key to move cursor to
[ Continue ] then press [ENTER] key then press [ENTER] key
again
赏屯屯屯屯屯屯屯屯屯屯屯 Enter Image Directory 屯屯屯屯屯屯屯屯屯屯屯屯屯?
? ?
?Enter the full path to the directory containing media images. ?
? ?
?Image Directory: |/usr/test__________________________________________| ?
? ?
?Note: media images must follow the naming convention VOL.000.000, etc. ?
? ?
? ?
? ?
耗哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪暮
篬 OK ] [ Cancel ] [ Help ]?
韧屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯图
-> Input the path name where VOL.000.000 is located as above
path name is /usr/test
赏屯屯屯屯屯屯屯屯屯屯屯 Enter Image Directory 屯屯屯屯屯屯屯屯屯屯屯屯屯屯?
? ?
?Installing: D-Link DFE-530TX PCI Fast Ethernet Device Driver (version 1.0?
? ?
?Do you want a FULL or PARTIAL installation? ?
? ?
耗哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪暮
篬 Full ] [ Partial ] [ Cancel ] [ Help ]?
韧屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯图
Using [TAB] key to move cursor to [ Full ] then press [ENTER] key
After the installation progress the following message is displayed
赏屯屯屯屯屯 Question 屯屯屯屯屯?
? Installation complete ?
耗哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪?
? [ OK ] ?
韧屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯?
Press [Enter] key then you will find out that
D-Link DFE-530TX PCI Fast Ethernet Device Driver (ver 1.0.2)
is added to the package list
Using [<-] key to move cursor back to "Host" menu item then
press [] key to get into pull down menu then move to "Exit"
then press [ENTER] key
Now that the driver is installed in the system successfully.
2. Using "netconfig" to configure the driver
/* A menu selection screen will be popped up */
At "Hardware" menu item press [] key to get into pull down menu then
move to "Add new LAN adapter" then press [ENTER] key
If you got a PCI NIC inserted on your machine, it will list as
following:
赏屯屯屯屯屯屯屯屯屯屯屯屯屯 Add new LAN adapter 屯屯屯屯屯屯屯屯屯屯屯屯屯屯?
篢he following adapters have been found: ?
黑哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪亢
撼* D-Link DFE-530TX PCI Fast Ethernet Adapter - PCI Bus 0, PCI Dev 11, PC澈
撼 澈
撼 澈
撼 澈
撼 澈
豪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪俸
篬 Configure hardware not listed above... ] ?
耗哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪暮
篬 Continue ] [ Cancel ] [ Help ]?
韧屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯图
If the "D-Link DFE-530TX PCI Fast Ethernet Adapter..." has been
displayed press [ENTER] directly, otherwise using [TAB] key to
move to "Configure hardware not listed above..." then press
[ENTER] key
赏屯屯屯屯屯屯屯屯屯屯屯屯屯 Add new LAN adapter 屯屯屯屯屯屯屯屯屯屯屯屯屯屯?
篠elect network adapter to be added: ?
黑哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪亢
撼* 3Com EtherLink 16/16TP Adapter ^?
撼 . *?
撼 . *?
撼 . *?
撼 . *?
撼 . *?
撼 . *?
撼 . *?
撼 D-Link DFE-530TX PCI Fast Ethernet Adapter *?
撼 . 澈
撼 . 澈
撼 . 澈
撼 . 澈
撼 . 澈
撼 . v?
豪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪俸
耗哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪暮
篬 Continue ] [ Cancel ] [ Help ]?
韧屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯图
Using [] key to move to "D-Link DFE-530TX PCI Fast Ethernet Adapter"
then press [ENTER] key.
赏屯屯屯屯屯屯屯屯屯屯 Network Driver Configuration 屯屯屯屯屯屯屯屯屯突
? ?
篍nter the configuration of D-Link DFE-530TX PCI Fast Ethernet Adapter:?
? ?
? 谀哪哪哪哪哪哪哪哪哪哪哪哪哪目 [ Advanced ] ?
? PCI Bus#: 硘 0_______________________|v? Options... ?
? 滥哪哪哪哪哪哪哪哪哪哪哪哪哪馁 ?
? 谀哪哪哪哪哪哪哪哪哪哪哪哪哪目 ?
? PCI Device#: 硘 0_______________________|v? ?
? 郎屯屯屯屯荒哪哪哪哪哪哪哪哪馁 ?
? 诤谀哪哪目耗哪哪哪哪哪哪哪哪目 ?
篜CI Function#: 澈? 9 ^篲_______________|v? ?
? 篮? 10 澈哪哪哪哪哪哪哪哪哪? ?
? 撼 11 澈 ?
? * - indicates 撼 12 *篿th other hardware ?
耗哪哪哪哪哪哪哪哪撼* 13 *耗哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪?
篬 OK ] 撼 14 v? [ Cancel ] [ Help ]?
韧屯屯屯屯屯屯屯屯豪哪哪哪俸屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯图
韧屯屯屯图
The above screen let you fill the information of where your PCI adapter
is located by specifying PCI Bus#, PCI Device# and PCI Function#.
Note1: If you can not make sure the PCI parameters or your PCI Device#
can not be found in the list, just leave them as default values,
continue the following installation, after the driver is
installed and system is re-linked, reboot the system then driver
will search PCI Ethernet card automatically.
"Advanced Options" let you specify what media type is connectted.
If you select it the following screen will be popped up
赏屯屯屯屯屯屯屯屯?Advanced Network Driver Configuration 屯屯屯屯屯屯屯?
? ?
篍nter the configuration of D-Link DFE-530TX PCI Fast Ehternet Adapter: ?
? ?
? 谀哪哪哪哪哪哪哪哪哪哪哪哪? ?
篗edia Type: 硘 Auto_________________|v? ?
? 郎屯屯屯屯屯屯屯屯屯荒哪哪? ?
? ?谀哪哪哪哪哪哪哪亢 ?
? * - indicat?? Auto 澈her hardware ?
耗哪哪哪哪哪哪暮 ? TP 澈哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪暮
篬 OK ] ?? TP_FD 澈el ] [ Help ]?
韧屯屯屯屯屯屯秃 ? TX100 澈屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯图
?? TX100_FD 澈
?滥哪哪哪哪哪哪哪俸
韧屯屯屯屯屯屯屯屯图
Select the connective media then press [ENTER] key to go back to
"Network Driver Configuration" screen.
Using [TAB] key to move cursor to "OK" then press [ENTER] key.
赏屯屯屯屯屯屯屯屯屯屯屯屯?Information 屯屯屯屯屯屯屯屯屯屯屯屯屯屯?
?-- Please verify adapter is set to the configuration just entered?
耗哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪?
? [ OK ] ?
韧屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯?
Press [ENTER] key.
赏屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯?Add Protocol 屯屯屯屯屯屯屯屯屯屯屯屯屯屯?
篠elect one networking product to be added to ?
篋-Link DFE-530TX PCI Fast Ethernet Adapter: ?
黑哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪亢
撼 HW D-Link DFE-530TX PCI Fast Ethernet Adapter 澈
撼* - SCO IPX/SPX 澈
撼 - SCO TCP/IP 澈
撼 澈
撼 澈
豪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪俸
耗哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪暮
篬 Add ] [ Cancel ] [ Help ]?
韧屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯图
Using [] key to move cursor to "SCO TCP/IP" then press [ENTER] key.
赏屯屯屯屯屯屯屯 SCO TCP/IP Configuration 屯屯屯屯屯屯屯屯?
? ?
? ?
? ?
? ?
? Local Host Name: |scoopen_____________| [ Advanced ]?
? IP Address: |192.9.200.1_________| Options... ?
? Netmask: |255.255.255.0_______| ?
築roadcast Address: |192.9.200.255_______| ?
? Domain Name: |scoopen.com_________| ?
? TCP connections: |256_________________| ?
? Pseudo ttys: |32__________________| ?
? ?
? ?
耗哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪?
? ?
?[ OK ] [ Cancel ] [ Help ]?
? ?
韧屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯?
Input the required information then use [TAB] key to move cursor to
"OK" then press [ENTER] key.
赏屯屯屯屯屯屯屯屯屯屯屯屯屯屯 Message 屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯突
?The following products were successfully configured into the system ?
?SCO TCP/IP ?
?D-Link DFE-530TX PCI Fast Ethernet Adapter - PCI Bus#0,PCI Device#13,P?
? ?
耗哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪?
篬 OK ] [ Help ] ?
韧屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯?
Press [ENTER] key
At "Hardware" menu item press [] key to get into pull down menu then
move to "Exit" then press [ENTER] key
赏屯屯屯屯屯屯屯屯屯屯屯 Question 屯屯屯屯屯屯屯屯屯屯屯屯?
? The Unix Kernel must be re-linked before the changes?
??? made here will have an effect. ?
? Do you want to re-link the kernel now? ?
耗哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪?
?[ YES ] [ NO ] ?
韧屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯?
Press [ENTER] key
Do you want this kernel to boot by default (y/n) y
Do you want the kernel environment rebuilt (y/n) y
3. Reboot unix
# shutdown -y -g0
***************************************************
* Another way to specify driver's PCI parameters *
***************************************************
. Another way to modify PCI parameters is at booting
time, shown as below:
1. Specify PCI Bus#, PCI Device# and PCI Function#
Boot
: unix net.mdi=d5B(0) net.param=(pcb:0,pcd:14,pcf:0)
2. Auto-search PCI adapter card
Boot
: unix net.mdi=d5B(0)
Note2: The IRQ number must match with the value set in ROM-BIOS before you
specify this value, please check it.
The IRQ for PCI bus can be accessed by pressing [DEL] key when
system is power on and choose the proper select item to set IRQ
for PCI bus.
Example: ROM PCI/ISA BIOS (2A4X5C31)
PCI/GREEN FUNCTION SETUP
AWARD SOFTWARE, INC.
Press [DEL] key --> PCI/GREEN FUNCTION SETUP
Slot 3 Using INT# : A-PIRQ1
.
.
.
PIRQ1# Connect IRQ: 5 By Single
~
我有一个D＿LINK网卡关于SCO的安装说明，你可以参照一下
D-Link DFE-530TX PCI Fast Ethernet Adapter Installation
for SCO OpenServer V5.0 MDI Driver
Getting Started
---------------
0. Login as root user. (On maintenance mode)
1. Using "custom" to install the driver
1.1 Prepare an image file
Copy d5B.IMG onto SCO OpenServer and rename it to VOL.000.000
# mkdir /usr/test
# doscp a:/<PATH>/d5B.IMG /usr/test/VOL.000.000
* <PATH> is the driver directory
1.2 Execute "custom"
/* A menu selection screen will be popped up */
Using [->] key to move cursor to "Software" menu item then
press [] key to get into pull down menu then move to
"Install New..." then press [ENTER] key
赏屯屯屯屯?Begin Installation on scoopen 屯屯屯屯屯?
? ?
? What host (machine) do you want to install from? ?
? ?
? 谀哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪目 ?
? ?*> From scoopen ??
? ? > From another host ??
? 滥哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪馁 ?
? ?
耗哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪?
篬 Continue ] [ Cancel ] [ Help] ?
韧屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯?
Select From scoopen and use [TAB] key to move cursor to
[ Continue ] then press [ENTER] key and press [] key to get
into pull down menu
赏屯屯屯屯屯屯屯屯屯屯屯?Select Media 屯屯屯屯屯屯屯屯屯屯屯屯?
? ?
? Insert media, and select media device. ?
? ?
? 谀哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪目 ?
? Media Device:硘Floppy Disk Driver 0_____________________|v??
? 郎屯屯屯屯屯屯屯屯屯屯屯屯荒哪哪哪哪哪哪哪哪馁 ?
? 黑哪哪哪哪哪哪哪哪哪哪哪亢 ?
? 撼*Floppy Disk Driver 0 澈 ?
? 撼 Media Images 澈 ?
耗哪哪哪哪哪哪哪暮滥哪哪哪哪哪哪哪哪哪哪馁耗哪哪哪哪哪哪哪哪哪暮
篬 Continue ] 韧屯屯屯屯屯屯屯屯屯屯屯图 [ Help ]?
韧屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯图
-> Select "Media Images" and use [TAB] key to move cursor to
[ Continue ] then press [ENTER] key then press [ENTER] key
again
赏屯屯屯屯屯屯屯屯屯屯屯 Enter Image Directory 屯屯屯屯屯屯屯屯屯屯屯屯屯?
? ?
?Enter the full path to the directory containing media images. ?
? ?
?Image Directory: |/usr/test__________________________________________| ?
? ?
?Note: media images must follow the naming convention VOL.000.000, etc. ?
? ?
? ?
? ?
耗哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪暮
篬 OK ] [ Cancel ] [ Help ]?
韧屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯图
-> Input the path name where VOL.000.000 is located as above
path name is /usr/test
赏屯屯屯屯屯屯屯屯屯屯屯 Enter Image Directory 屯屯屯屯屯屯屯屯屯屯屯屯屯屯?
? ?
?Installing: D-Link DFE-530TX PCI Fast Ethernet Device Driver (version 1.0?
? ?
?Do you want a FULL or PARTIAL installation? ?
? ?
耗哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪暮
篬 Full ] [ Partial ] [ Cancel ] [ Help ]?
韧屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯图
Using [TAB] key to move cursor to [ Full ] then press [ENTER] key
After the installation progress the following message is displayed
赏屯屯屯屯屯 Question 屯屯屯屯屯?
? Installation complete ?
耗哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪?
? [ OK ] ?
韧屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯?
Press [Enter] key then you will find out that
D-Link DFE-530TX PCI Fast Ethernet Device Driver (ver 1.0.2)
is added to the package list
Using [<-] key to move cursor back to "Host" menu item then
press [] key to get into pull down menu then move to "Exit"
then press [ENTER] key
Now that the driver is installed in the system successfully.
2. Using "netconfig" to configure the driver
/* A menu selection screen will be popped up */
At "Hardware" menu item press [] key to get into pull down menu then
move to "Add new LAN adapter" then press [ENTER] key
If you got a PCI NIC inserted on your machine, it will list as
following:
赏屯屯屯屯屯屯屯屯屯屯屯屯屯 Add new LAN adapter 屯屯屯屯屯屯屯屯屯屯屯屯屯屯?
篢he following adapters have been found: ?
黑哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪亢
撼* D-Link DFE-530TX PCI Fast Ethernet Adapter - PCI Bus 0, PCI Dev 11, PC澈
撼 澈
撼 澈
撼 澈
撼 澈
豪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪俸
篬 Configure hardware not listed above... ] ?
耗哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪暮
篬 Continue ] [ Cancel ] [ Help ]?
韧屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯图
If the "D-Link DFE-530TX PCI Fast Ethernet Adapter..." has been
displayed press [ENTER] directly, otherwise using [TAB] key to
move to "Configure hardware not listed above..." then press
[ENTER] key
赏屯屯屯屯屯屯屯屯屯屯屯屯屯 Add new LAN adapter 屯屯屯屯屯屯屯屯屯屯屯屯屯屯?
篠elect network adapter to be added: ?
黑哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪亢
撼* 3Com EtherLink 16/16TP Adapter ^?
撼 . *?
撼 . *?
撼 . *?
撼 . *?
撼 . *?
撼 . *?
撼 . *?
撼 D-Link DFE-530TX PCI Fast Ethernet Adapter *?
撼 . 澈
撼 . 澈
撼 . 澈
撼 . 澈
撼 . 澈
撼 . v?
豪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪俸
耗哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪暮
篬 Continue ] [ Cancel ] [ Help ]?
韧屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯图
Using [] key to move to "D-Link DFE-530TX PCI Fast Ethernet Adapter"
then press [ENTER] key.
赏屯屯屯屯屯屯屯屯屯屯 Network Driver Configuration 屯屯屯屯屯屯屯屯屯突
? ?
篍nter the configuration of D-Link DFE-530TX PCI Fast Ethernet Adapter:?
? ?
? 谀哪哪哪哪哪哪哪哪哪哪哪哪哪目 [ Advanced ] ?
? PCI Bus#: 硘 0_______________________|v? Options... ?
? 滥哪哪哪哪哪哪哪哪哪哪哪哪哪馁 ?
? 谀哪哪哪哪哪哪哪哪哪哪哪哪哪目 ?
? PCI Device#: 硘 0_______________________|v? ?
? 郎屯屯屯屯荒哪哪哪哪哪哪哪哪馁 ?
? 诤谀哪哪目耗哪哪哪哪哪哪哪哪目 ?
篜CI Function#: 澈? 9 ^篲_______________|v? ?
? 篮? 10 澈哪哪哪哪哪哪哪哪哪? ?
? 撼 11 澈 ?
? * - indicates 撼 12 *篿th other hardware ?
耗哪哪哪哪哪哪哪哪撼* 13 *耗哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪?
篬 OK ] 撼 14 v? [ Cancel ] [ Help ]?
韧屯屯屯屯屯屯屯屯豪哪哪哪俸屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯图
韧屯屯屯图
The above screen let you fill the information of where your PCI adapter
is located by specifying PCI Bus#, PCI Device# and PCI Function#.
Note1: If you can not make sure the PCI parameters or your PCI Device#
can not be found in the list, just leave them as default values,
continue the following installation, after the driver is
installed and system is re-linked, reboot the system then driver
will search PCI Ethernet card automatically.
"Advanced Options" let you specify what media type is connectted.
If you select it the following screen will be popped up
赏屯屯屯屯屯屯屯屯?Advanced Network Driver Configuration 屯屯屯屯屯屯屯?
? ?
篍nter the configuration of D-Link DFE-530TX PCI Fast Ehternet Adapter: ?
? ?
? 谀哪哪哪哪哪哪哪哪哪哪哪哪? ?
篗edia Type: 硘 Auto_________________|v? ?
? 郎屯屯屯屯屯屯屯屯屯荒哪哪? ?
? ?谀哪哪哪哪哪哪哪亢 ?
? * - indicat?? Auto 澈her hardware ?
耗哪哪哪哪哪哪暮 ? TP 澈哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪暮
篬 OK ] ?? TP_FD 澈el ] [ Help ]?
韧屯屯屯屯屯屯秃 ? TX100 澈屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯图
?? TX100_FD 澈
?滥哪哪哪哪哪哪哪俸
韧屯屯屯屯屯屯屯屯图
Select the connective media then press [ENTER] key to go back to
"Network Driver Configuration" screen.
Using [TAB] key to move cursor to "OK" then press [ENTER] key.
赏屯屯屯屯屯屯屯屯屯屯屯屯?Information 屯屯屯屯屯屯屯屯屯屯屯屯屯屯?
?-- Please verify adapter is set to the configuration just entered?
耗哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪?
? [ OK ] ?
韧屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯?
Press [ENTER] key.
赏屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯?Add Protocol 屯屯屯屯屯屯屯屯屯屯屯屯屯屯?
篠elect one networking product to be added to ?
篋-Link DFE-530TX PCI Fast Ethernet Adapter: ?
黑哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪亢
撼 HW D-Link DFE-530TX PCI Fast Ethernet Adapter 澈
撼* - SCO IPX/SPX 澈
撼 - SCO TCP/IP 澈
撼 澈
撼 澈
豪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪俸
耗哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪暮
篬 Add ] [ Cancel ] [ Help ]?
韧屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯图
Using [] key to move cursor to "SCO TCP/IP" then press [ENTER] key.
赏屯屯屯屯屯屯屯 SCO TCP/IP Configuration 屯屯屯屯屯屯屯屯?
? ?
? ?
? ?
? ?
? Local Host Name: |scoopen_____________| [ Advanced ]?
? IP Address: |192.9.200.1_________| Options... ?
? Netmask: |255.255.255.0_______| ?
築roadcast Address: |192.9.200.255_______| ?
? Domain Name: |scoopen.com_________| ?
? TCP connections: |256_________________| ?
? Pseudo ttys: |32__________________| ?
? ?
? ?
耗哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪?
? ?
?[ OK ] [ Cancel ] [ Help ]?
? ?
韧屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯?
Input the required information then use [TAB] key to move cursor to
"OK" then press [ENTER] key.
赏屯屯屯屯屯屯屯屯屯屯屯屯屯屯 Message 屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯突
?The following products were successfully configured into the system ?
?SCO TCP/IP ?
?D-Link DFE-530TX PCI Fast Ethernet Adapter - PCI Bus#0,PCI Device#13,P?
? ?
耗哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪?
篬 OK ] [ Help ] ?
韧屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯?
Press [ENTER] key
At "Hardware" menu item press [] key to get into pull down menu then
move to "Exit" then press [ENTER] key
赏屯屯屯屯屯屯屯屯屯屯屯 Question 屯屯屯屯屯屯屯屯屯屯屯屯?
? The Unix Kernel must be re-linked before the changes?
??? made here will have an effect. ?
? Do you want to re-link the kernel now? ?
耗哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪哪?
?[ YES ] [ NO ] ?
韧屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯屯?
Press [ENTER] key
Do you want this kernel to boot by default (y/n) y
Do you want the kernel environment rebuilt (y/n) y
3. Reboot unix
# shutdown -y -g0
***************************************************
* Another way to specify driver's PCI parameters *
***************************************************
. Another way to modify PCI parameters is at booting
time, shown as below:
1. Specify PCI Bus#, PCI Device# and PCI Function#
Boot
: unix net.mdi=d5B(0) net.param=(pcb:0,pcd:14,pcf:0)
2. Auto-search PCI adapter card
Boot
: unix net.mdi=d5B(0)
Note2: The IRQ number must match with the value set in ROM-BIOS before you
specify this value, please check it.
The IRQ for PCI bus can be accessed by pressing [DEL] key when
system is power on and choose the proper select item to set IRQ
for PCI bus.
Example: ROM PCI/ISA BIOS (2A4X5C31)
PCI/GREEN FUNCTION SETUP
AWARD SOFTWARE, INC.
Press [DEL] key --> PCI/GREEN FUNCTION SETUP
Slot 3 Using INT# : A-PIRQ1
.
.
.
PIRQ1# Connect IRQ: 5 By Single
~
thorn 2001-08-30
- 打赏
- 举报
老兄，readme里面是这样说得吗？
yijn 2001-08-29
- 打赏
- 举报
谢谢！我试一下如果没问题就给分，HEIHEI!
kmyangyl 2001-08-29
- 打赏
- 举报
下载后，放入本地，重新安装网卡，选择从本地安装。
thorn 2001-08-28
- 打赏
- 举报
download nic driver from:
http://www.tp-link.com.cn
uncompress,under "sco" directory,
you will find "readme.doc"......
That's Ok.Good luck!
http://www.tp-link.com.cn
uncompress,under "sco" directory,
you will find "readme.doc"......
That's Ok.Good luck!
